I've been specifying and installing residential and commercial boiler systems for 9 years — closer to 8 and a half if you subtract the first year of pure guesswork. I've personally made and documented at least six significant mistakes on boiler orders, totaling roughly $4,800 in wasted budget (mostly return shipping and rush replacement parts). Now I keep a checklist taped to my desk for exactly this reason.
This FAQ covers the questions I actually get from installers, property managers, and homeowners who call me after reading something confusing on a forum. No fluff. If something doesn't apply to your situation, I'll say so.
The honest answer depends on fuel type, water quality, and whether anyone bothered to commission the system properly. According to ASHRAE and general industry data, conventional cast-iron boilers typically run 20–30 years. Condensing models generally see 15–20 years, largely because they have more parts and tighter tolerances.
I'll give you a specific one: in 2017 we installed a Burnham Series 2 conventional boiler in a multifamily building. By 2021, the heat exchanger started leaking. Was it the boiler's fault? No — we later found out the building's water chemistry was off and nobody had flushed the system since installation. The boiler did its job. The installation didn't. If you're in a hard-water area, budget for water treatment before you budget for a replacement boiler.
Burnham's own maintenance documentation (burnham.com) recommends annual professional inspections for both residential and commercial units. I'd treat that as the absolute minimum, not a suggestion.
First: find the exact model number on your boiler's data plate. Burnham has made dozens of gas boiler configurations over the years — pilot light procedures vary by model. What I'm about to describe covers most standing-pilot configurations, but your manual takes priority over anything I say here.
Typical sequence: turn the gas valve to OFF, wait 5 minutes, locate the pilot assembly (near the burner tray), set the thermostat to its lowest setting, turn the gas valve to PILOT, press and hold the reset button, apply a flame to the pilot orifice, hold for 30–60 seconds after the flame catches, then release and turn the valve to ON.
In 2020, I almost did this wrong. I skipped the 5-minute wait because I was in a hurry. The gas hadn't fully cleared. Nothing happened — no explosion, no dramatic story — but I got a face full of gas smell and a lesson I won't forget. If you smell gas at any point, stop. Leave the area. Call your gas provider.
Note to self: the 5-minute wait isn't optional. Ever.
Everything I'd read said condensing boilers were always worth it for the efficiency gains. In practice, the answer is more nuanced.
A condensing boiler captures heat from exhaust gases that a conventional boiler sends up the flue. Energy Star-rated condensing models can reach 95% AFUE, compared to 80–85% for conventional models. On paper, that's a clear win.
But here's where it gets real: condensing boilers achieve those numbers best with lower return-water temperatures. If your existing radiators need high-temperature water (say, 160°F+), the boiler spends more time in non-condensing mode, and your real-world savings shrink considerably. I upgraded my own house to a Burnham condensing unit in 2019 — worked great because I also swapped the radiators. A friend of mine did the boiler only, kept his old high-temp radiators, and saw maybe half the savings he expected.
If you're planning to stay in the building for 7+ years and have compatible low-temp heat distribution, the math works. If you're flipping the property in 3 years or running high-temp cast iron, run the numbers carefully before committing.
In most cases, yes — provided your boiler uses a standard 24V thermostat circuit. The ecobee install guide (ecobee.com, accessed January 2025) requires a C-wire or the included power extender kit. Most modern Burnham gas boilers have 24V terminals that are compatible, but older or commercial models may use different control voltages.
I made the classic mistake in 2019: bought an ecobee before checking the boiler's control board. My customer's boiler used a millivolt system. No C-wire, no simple swap. We ended up adding a transformer and an isolation relay — probably $180 in parts and extra labor that could have been avoided with a two-minute look at the wiring diagram.
If you're not sure: find your boiler's wiring diagram (usually inside the access panel) and look for terminals labeled R, W, and C. If you see those, you're probably fine. If you see millivolt or proprietary control labels, call Burnham tech support before you buy anything.
For ecobee specifically: pull the thermostat off its wall plate, hold the reset button on the back for about 10 seconds, and remount. That restores factory settings. You'll need to reconnect to Wi-Fi and rebuild your schedule.
But here's my honest advice: don't reset first. Diagnose first. In 2022, I reset a customer's ecobee three times chasing a "frozen display" issue. Fourth call, I realized the actual problem was a tripped breaker on the boiler circuit — the thermostat had no power, not a software glitch. Three resets, two hours, and a very patient customer later, a 30-second breaker fix solved it.
If your thermostat is blank, unresponsive, or acting erratically, check the boiler's power supply and circuit breaker before you touch any reset button. You'll save yourself the hassle of reconfiguring everything.
Short answer: it shouldn't have. Burnham is a boiler brand — residential and commercial heating equipment. Oxyshred is a fat-burner supplement made by a completely different company. The word "burner" is where the confusion happens.
In the boiler world, a burner is the component that mixes fuel and air for combustion. It's a $150–$400 replacement part, not a weight-loss product. So if you searched for "burnham fat burner" hoping to find a supplement, you're in the wrong corner of the internet. If you searched for "burnham burner" and got wellness ads, same issue — your search engine found the word and ran with it.
If you're actually looking for a Burnham boiler burner assembly or pilot burner part, check the parts section at burnham.com or call their tech support line with your model number. They'll point you to the right component. (And if you're genuinely looking for oxyshred, you'll need a different website entirely — that's not a product I can help with.)
I recommend Burnham for a lot of situations — durable cast-iron construction, solid technical support, and a product line that genuinely covers residential through commercial. But I'd be doing you a disservice if I pretended it's always the answer.
If you need the lowest possible upfront cost and you're comfortable with a shorter service life, there are budget-tier options that work fine for light-duty applications. Burnham's value shows up over time, not on the initial invoice.
If your building barely needs heat — say, a mild climate with minimal winter demand — a heat pump system might be a more energy-efficient overall fit. That's not a knock on Burnham; it's just matching the tool to the job. I've specified both. They solve different problems.
And if you need equipment delivered next week, check local distributor stock before you commit to a specific model. Burnham's lead times are reasonable, but they're not instant, and I've seen projects get delayed because someone assumed otherwise.
The best boiler is the one that matches your building, your budget, and your timeline. Sometimes that's Burnham. Sometimes it isn't. Either way, now you know what to check before you commit.